1
您的位置: 线上活动  >  在线答题  >  答题题库

M9

2023-12-01 20:38:38.322.0.32904

M9 在线考试 答题题目
1、 The backside of the title page should be left blank to avoid the need for revision and potential loss of the inserted airplane serial and registration numbers.
  • A、标题页的背面应留白,以免需要改版,以及可能遗漏插入的飞机序列号和注册号。
  • B、标题页的背面应保持空白,以备需要插入可能遗漏的飞机序列号和注册号。
  • C、标题页的背面应有充分的内容,以免被插入遗漏的飞机序列号和注册号。


  • 2、 如果一个词在一个特定的技术领域只有非常少的人理解,就会对交流造成干扰。
  • A、Misunderstanding will occur if a word is only understood by a large amount of people in a special technical area.
  • B、If a word is only known by quite a small amount of people in a special technical field, there will be communication interference.
  • C、If a word is only understood by a very small number of people in a specific technical area, it will cause interference in communication.


  • 3、 在高压电环境下工作时,请遵守安全注意事项。
  • A、Obey the safety precautions when you do work with high voltages.
  • B、Obey the safety warnings when you do work with high impedance.
  • C、Obey the safety cautions when you do work with high capacitance.


  • 4、 发动机系统中包含螺旋桨轴和减速器的部分。
  • A、The section of the engine system which contains the turbine shafts and reduction gears.
  • B、The section of the engine system which contains the propeller shafts and reduction gears.
  • C、The section of the engine system which contains the connection shafts and reduction gears.


  • 5、 These parts can easily bend, break or become incorrectly aligned.
  • A、这些部件很容易弯曲、断裂或不正确地对齐。
  • B、这些部件很容易焊接、损坏或不正确地对齐。
  • C、这些部件很容易焊接、断裂或不正确地装配。


  • 6、 如果不使用隔页签,应提供一种识别方法,便于确定每个系统或章节的位置。
  • A、If no tabs are used, an identification method should be supplied to facilitate the location of each system or section.
  • B、If tab dividers are not used, a method of identification shall be provided to permit easy location of each System or Chapter.
  • C、An identification way should be offered to locate the system and chapter easily if the dividers are improper.


  • 7、 Measure the bend radius of the hose from the point where the bend starts.
  • A、从软管开始弯曲的地方测量软管的弯曲半径。
  • B、在软管弯曲的地方开始测量软管的内径。
  • C、从软管弯曲的内侧开始测量软管弯曲的角度。


  • 8、 Put the mask on and breathe through it to make sure that the oxygen supply is correct.
  • A、戴上氧气面罩并进行呼吸,确认其供氧正常。
  • B、在佩戴氧气面罩前进行深呼吸,确认血液中氧气充足。
  • C、为确保供氧正常,请不要摘下氧气面罩并进行呼吸。


  • 9、 马赫数是真空速与音速的比值。
  • A、Mach digit is the percent of true airspeed to the speed of sound.
  • B、Mach number is the ratio of true airspeed to the speed of sound.
  • C、Mach number is the proportion of real airspeed to the speed of light.


  • 10、 Personnel must be familiar with the emergency safety procedures prior to using the material.
  • A、了解工作程序最好的人,可以使用材料。
  • B、在使用材料之前,人员必须熟悉紧急安全程序。
  • C、最先熟悉紧急撤离程序的人可以使用材料。


  • 11、 Procedures shall be provided for all airplanes for all cases of engine failure during takeoff and in flight.
  • A、在起飞和飞行期间,在发动机故障的情况下应对飞机采取相应措施。
  • B、对于所有飞机在起飞和飞行过程中发生的所有发动机故障,应提供相应的程序。
  • C、在起飞和飞行期间,对于飞机的各种发动机故障,应执行相应程序。


  • 12、 If it is possible that the temperature values will be more than the permitted limits, decrease the power.
  • A、如果温度值可能超过允许的限度,降低功率。
  • B、如果温度值可能超过允许的限度,切断电源。
  • C、如果温度值可能超过最大限度,减少用电。


  • 13、 WARNING,if not correctly followed, could result in personal injury, or loss of life.
  • A、注意,如果没有正确执行以下步骤,会导致人员伤亡。
  • B、警告,如果你不正确听从指挥,则会导致人员伤亡。
  • C、如果没有正确遵循警告里的要求,将会导致人员伤亡。


  • 14、 确保液压油箱内的液压油高于最低液面。
  • A、Make sure that the oil in the hydraulic tank is above the minimum lever.
  • B、Make sure that the fluid in the hydraulic reservoir is above the minimum level.
  • C、Make sure that the fluid in the fuel reservoir is below the maximum level.


  • 15、 The primary function of the hydraulic pressure system is to supply pressure for the operation of the flight controls.
  • A、液压系统的主要压力用于飞行控制系统。
  • B、飞行控制运行所需的压力来源于起主要作用的液压系统。
  • C、液压系统的主要功能是为飞行控制系统的操作提供压力。


  • 16、 易燃物品与工作区域保持至少50英尺的距离。
  • A、A maximum distance of 50 feet is required between consumable materials and the work area.
  • B、Keep flammable materials at a minimum distance of 50 feet from the work area.
  • C、Explosive materials must be kept at least 50 feet away from the work area.


  • 17、 确保能够通过观测计看见滑油油位。
  • A、Make sure that you can see the oil level through the sight gauge.
  • B、Make sure that the oil quantity is shown on the oil level indicator.
  • C、You can read the oil level on the oil level gauge.


  • 18、 当你替换一个单词时,总是确保你选择的替代词不会改变句子的意思。
  • A、When you change a word, always assure that the alternative you choose does not change the sequence of the sentence.
  • B、When you replace a word, always make sure that the alternative you select does not change the meaning of the sentence.
  • C、When you exchange a word, always ensure that the alternative you pick does not change the order of the sentence.


  • 19、 Pressure switches connected to the individual pump outlets are used to indicate the pump status.
  • A、压力电门用于连接单个泵出口来指示泵的状态。
  • B、连接着单个泵出口的压力电门用于指示泵的状态。
  • C、压力电门连接的单个泵出口用于指示泵的状态。


  • 20、 外部标牌和标记用于地面勤务说明、检查、警戒、警告等。
  • A、Exterior Placards and Markings are required for ground servicing instructions, inspections, cautions, warnings.
  • B、Exterior Labels and Markings are required for ground servicing instructions, inspections, cautions, warnings.
  • C、Exterior Placards and Markings are required for ground servicing instructions, inspections, warnings, cautions.


  • 21、 移除传感器以便接近传感器相邻的结构。
  • A、To gain entry to the nearby structure, take out the sensor.
  • B、Remove the sensor to get access to the adjacent structure.
  • C、Disassemble the sensor to get access to the adjacent structure.


  • 22、 The circulation of the air in the components is such that the temperature for specific component is not out of the limit.
  • A、该部件中的空气循环使得特定部件的温度不超限。
  • B、某些部件的温度不超限因此该部件中的空气能够流动。
  • C、该部件中的空气的旋转和特殊部件的温度均不超限。


  • 23、 Make sure that there is clearance between the lever and the roller.
  • A、保证手柄和滚柱之间是干净的。
  • B、确保杆和滚柱之间有连接。
  • C、确保杆和滚轮之间有间隙。


  • 24、 Lift the cylinder above its installed position.
  • A、从安装位置向上提起气瓶。
  • B、向上提起做动筒到安装位置。
  • C、提起并安装气缸到位。


  • 25、 用上部的锁机构安装中下显示组件。
  • A、Use the upper latch mechanism to lock the lower display unit in the middle.
  • B、The latch mechanism at the top is used to secure the center display unit on the bottom.
  • C、The center lower display unit is installed with the latch mechanism at the top.


  • 26、 Remove and discard the cotter pins and the nuts.
  • A、拆除并丢弃开口销和螺栓。
  • B、拆除并报废开口销和螺帽。
  • C、拆除并破坏开口销和螺钉。


  • 27、 Do not open the housing while the electrical power is connected.
  • A、电源接通后再打开外壳。
  • B、电源接通前不要打开外壳。
  • C、电源接通时不要打开外壳。


  • 28、 Arrows shall be used to indicate flow direction when needed to understand the schematic diagram.
  • A、当必须理解原理图时,最好使用箭头来画出流动方向。
  • B、当需要理解原理图时,应该使用箭头来指示流动方向。
  • C、当需要理解计划表时,应该使用线条来指示流动方向。


  • 29、 当油箱内正压或负压力过大时释压活门可防止机翼结构损坏。
  • A、When there are too many positive or subtractive pressure in the fuel tanks,the pressure relief valve eliminates damage to the wing structure.
  • B、When there is too much plus or minus pressure in the fuel tanks,the pressure relief valve previews damage to the wing structure.
  • C、The pressure relief valve prevents damage to the wing structure when there is too much positive or negative pressure in the fuel tanks.


  • 30、 句型应简单直接,无需阐述明显多余的和过于基础的信息。应避免讨论理论知识,除非该理论知识对实际操作的理解和施工是必要的。
  • A、Sentence forms shall be simple and direct, avoiding the obvious, the elementary and discussions of theory except where essential for practical understanding and application.
  • B、Sentence forms shall be simple and direct, avoiding the obvious and the elementary, and omitting discussions of theory except where essential for practical understanding and application.
  • C、Sentence forms shall be simple and direct so as to avoid the obvious and the elementary, and to omit discussions of theory except where essential for practical understanding and application.


  • 31、 确保客舱内的压力差不多为零。
  • A、Make sure that the pressure in the cabin is almost zero.
  • B、Verify that the cabin pressure is not above zero.
  • C、Ensure that the pressure in the cabin is completely zero.


  • 32、 许多读者的英语知识有限,复杂的句子结构和许多英语单词所具有的大量的意义和同义词会引起混淆。
  • A、Many readers have little knowledge of English. Complex sentence structure and the large number of meanings and antonyms that many English words have can cause misconception.
  • B、Many readers have a limited knowledge of English. Complex sentence structure and the large number of meanings and synonyms that many English words have can cause confusion.
  • C、Many readers have a little knowledge of English. Complex sentence structure and the large number of meanings and homonyms that many English words have can cause frustration.


  • 33、 The Type Certificate will not be issued to the applicant unless the findings are completely settled.
  • A、只要发现的问题得到彻底解决,就会向申请方颁发补充型号合格证。
  • B、如果发现的问题得不到彻底解决,就不会向申请方颁发型号合格证。
  • C、型号合格证的颁发与否取决于是否彻底解决了发现的问题。


  • 34、 喷油嘴堵塞会导致错误的操作。
  • A、A blocked oil jet cannot enhance performance.
  • B、Incorrect operation is caused by a blocked oil tank.
  • C、A blocked oil jet can cause incorrect operation.


  • 35、 如果用了很大的力来打开组件,则检查控制连杆。
  • A、If you must apply a strike to open the unit, examine the control linkage.
  • B、If you must apply an unusual force to open the unit, examine the turnbuckle.
  • C、If you must apply an unusual force to open the unit, examine the control linkage.


  • 36、 Make sure that the tension in the cables is correct.
  • A、确保钢索的张力是合适的。
  • B、确保电缆的压力是正确的。
  • C、确保钢索的压力是正确的。


  • 37、 The Maintenance Manual is furnished to the Purchaser at the time of aircraft delivery.
  • A、The Maintenance Manual is supplied by the manufacturer at the time of aircraft delivery.
  • B、When delivering the aircraft, the Maintenance Manual is provided to the buyer.
  • C、The Maintenance Manual is prepared by the manufacturer before the aircraft is delivered.


  • 38、 Make sure that the fluid that goes through the tube has no bubbles.
  • A、确保通过管路的流体没有气泡。
  • B、确保通过管路的油液没有杂质。
  • C、确保液压油流经管路没有阻碍。


  • 39、 以60度增量逆时针转动调节器。
  • A、Turn the adjuster clockwise to increase 60 Deg.
  • B、Turn the adjuster counterclockwise in increments of 60 Deg.
  • C、Decrease 60 Deg. to turn the adjuster counterclockwise.


  • 40、 如果在密闭空间使用溶剂,请确保工作区域有良好的空气流通。
  • A、If you use solvent in a closed space, make sure that there is good airflow in the work area.
  • B、When using composite in confined space, make sure it has good ventilation.
  • C、You can not use sealant in enclosed space on condition that there is no good ventilation.


  • 41、 应急照明是指单独的、独立的子系统,在主电源故障的情况下提供照明。
  • A、Emergency illumination refers to an individual and dependent subsystem which is used to provide lighting when the main electrical power fails.
  • B、Emergency lighting can provide illumination for an individual and independent subsystem in case of main electrical power failure.
  • C、Emergency lighting is the separate and independent subsystem used to provide illumination in case of primary electrical power failure.


  • 42、 To make the curing process slower, decrease the heat that you apply to the compound.
  • A、为使分解过程变得更慢,减少你对混合物的加热。
  • B、为使蠕变过程变得更慢,减少你对复合材料的加热。
  • C、为使固化过程变得更慢,减少你对化合物的加热。


  • 43、 升降舵的行程受升降舵动力控制组件的行程限制。
  • A、Elevator move is limited by the move of the elevator power control units.
  • B、Elevator trip is limited by the move of the elevator power control units.
  • C、Elevator travel is limited by the stroke of the elevator power control units.


  • 44、 Remove the valve located adjacent to pump.
  • A、拆下活门旁边的泵。
  • B、拆下位于泵上的活门。
  • C、拆下泵旁边的活门。


  • 45、 所有页面上必须有制造商的报头,出版物标题,飞机型号,发行或修订日期
  • A、The manufacturer's marks, publication title, airplane model, and issue or revision date must shown on all pages.
  • B、The manufacturer's headline, publication title, airplane model, and issue or revision date must print on all pages.
  • C、The manufacturer's masthead, publication title, airplane model, and issue or revision date must appear on all pages.


  • 46、 设置控制器以获得最大推力。
  • A、Preset the control to get maximum thrust.
  • B、Set the control to get maximum thrust.
  • C、Reset the control to get the maximum force .


  • 47、 用力过大会损坏密封件。
  • A、Too much force can cause damage to the sealing components.
  • B、Excessive force may damage the seal.
  • C、Too much force can cause damage to the contact surface.


  • 48、 在描述飞机起落架的部分,应说明警告系统的工作原理。
  • A、When describing the airplane's Landing Gear, how its indication system functions shall be explained.
  • B、When describing the airplane's Landing Gear, how its emergency response system functions shall be explained.
  • C、In the description of the airplane's Landing Gear, how its warning system functions shall be explained.


  • 49、 This specification will meet the applicable government regulatory requirements.
  • A、本规范将满足适用的政府监管要求。
  • B、此指令符合适航官方要求。
  • C、此规范适用于相关政府部门的要求。


  • 50、 The diagram shall be arranged so that the flow of the system can be traced with a minimum of effort.
  • A、应排布线路图,以便可以监测系统的最小流量。
  • B、横隔板的布局方式使得追查系统流向的工作变得不费力气。
  • C、图表的排列应便于花最小的力气即可追踪系统的流程。


  • 51、 Do not do this procedure in the hangar.
  • A、不要在机库里进行这项程序。
  • B、不要在车间内进行这项程序。
  • C、不要在机坪上进行这项程序。


  • 52、 此工具是可选的。
  • A、This tool is mandatory.
  • B、This tool is optional.
  • C、This tool is necessary.


  • 53、 The color of the indicator changes to green.
  • A、探头的颜色变为绿色。
  • B、指示器的颜色变为绿色。
  • C、显示器的颜色变为绿色。


  • 54、 Clean the exterior of the equipment and its mounting shelf hardware using a vacuum cleaner and brush.
  • A、用真空清洁器和刷子清洁设备的内部及其底座。
  • B、用真空清洁器和刷子清洁设备的外表面以及安装架。
  • C、真空清洁设备及硬件设施的表面涂层。


  • 55、 Use the passive voice only when it is really necessary.
  • A、仅在真正需要时才会使用被动时态。
  • B、当真正需要时仅使用被动时态。
  • C、当真正需要时仅使用主动时态。


  • 56、 Tighten the nuts but do not torque them at this time.
  • A、拧松螺钉,但同时不要给它们打力矩。
  • B、拧紧螺栓,但此时不要扭矩它们。
  • C、拧紧螺母,但此时不要给它们打力矩。


  • 57、 CORROSION INHIBITING COMPOUND MAY BE PRESENT IN CORROSION SUSCEPTIBLE LOCATIONS.
  • A、防腐剂可能存在于腐蚀严重的部位。
  • B、腐蚀敏感的部位可以安装防腐组件。
  • C、易受腐蚀的部位可能有防腐剂。


  • 58、 交换1、2号计算机,然后再做测试。
  • A、Replace the No. 1 and No. 2 computers. Then do the test again.
  • B、Interchange the No. 1 and No. 2 computers. Then do the test again.
  • C、Repair the No. 1 and No. 2 computers. Then do the test again.


  • 59、 The system interface circuits adapt to the physical properties of the connected systems.
  • A、系统接口电路适配已连接系统的物理特征。
  • B、系统的电路跳开关符合连接系统的物理特性。
  • C、系统电路的物理特点与所连接系统相匹配。


  • 60、 你可以从ABC的经销商或工厂的客户服务代表那里获得适当的表格副本和需要填写的条目的说明。
  • A、Copies of the appropriate forms and a description of the entries to be completed are available to you from an ABC dealer or Factory Customer Service Representative.
  • B、Copies of the proper forms and a description of the items to be completed are available to you from an ABC trader or Production Customer Service Representative.
  • C、The ABC trader or Production Customer Service Representative could provide the proper form copies and the description of the items to be accomplished available.


  • 微信扫一扫 在线答题 在线出卷 随机出题小程序 闯关答题软件 出题答题小程序